Linux Network Configuration and Troubleshooting Commands 1. ifconfig. ifconfig (interface configurator) command is use to initialize an interface, assign IP Address to interface and enable or disable interface on demand. With this command you can view IP Address and Hardware / MAC address assign to interface and also MTU (Maximum transmission unit) size.
The Linux Operating System boasts kernel based networking support written almost entirely from scratch. The performance of the tcp/ip implementation in recent kernels makes it a worthy alternative to even the best of its peers. This document aims to describe how to install and configure the Linux networking software and associated tools. 1. NET3-4-HOWTO, Linux Networking HOWTO. Updated: Aug 1999. Aims to describe how to install and configure the Linux networking software and associated tools. ADSL-Bandwidth-Management-HOWTO, ADSL Bandwidth Management HOWTO. Updated: Apr 2003. Describes how to configure a linux router to more effectively manage outbound traffic on an ADSL modem. Sep 09, 2013 · For your Linux server to become a router, you have to enable packet forwarding. In simple terms packet forwarding enables packets to flow through the Linux box from one network to another. The Linux kernel configuration parameter to activate this is named net.ipv4.ip_forward and can be found in the file /etc/sysctl.conf. Remove the "#" from the Linux Networking−HOWTO: Author: Joshua Drake poet@linuxports.com v1.6.2, December 1999 A www.linuxports.com document for the Linux Documentation Project 1.Introduction. 2.Document History • 2.1 Feedback 3.How to use this HOWTO. • 3.1 Conventions used in this document 4.General Information about Linux Networking. • 4.1 Linux Networking This section applies to distros using a version of sysconfig with bonding support, for example, SuSE Linux Enterprise Server 9. SuSE SLES 9’s networking configuration system does support bonding, however, at this writing, the YaST system configuration front end does not provide any means to work with bonding devices.
Howto configure the Linux kernel / net / ax25 Amateur Radio protocols and AX.25 device configuration 19971130Now in an own category to make correct compilation of the AX.25 stuff easier Joerg Reuter DL1BKE 19980129Moved to net/ax25/Config.in, sourcing device drivers. HAMRADIO depends on NET (on/off) Amateur Radio support If you want to connect your Linux box to an amateur
We'll look at some additional aspects of networking on Unix and Linux systems in next week's post. Read more of Sandra Henry-Stocker's Unix as a Second Language blog and follow the latest IT news On Linux, one of the basic things you do is configure the network. Once you make changes, you have to restart the networking service in order for the changes to take effect. In this article, I will show you how to configure the network easily and restart them properly on Debian Linux. Let's get started.
Fedora Linux uses the Grub staged bootloader system where the first stage bootloader code (boot.img) is run from the MBR, but depending on the version of Grub, the following sequence of events is different.
Linux Networking−HOWTO: Author: Joshua Drake poet@linuxports.com v1.6.2, December 1999 A www.linuxports.com document for the Linux Documentation Project 1.Introduction. 2.Document History • 2.1 Feedback 3.How to use this HOWTO. • 3.1 Conventions used in this document 4.General Information about Linux Networking. • 4.1 Linux Networking This section applies to distros using a version of sysconfig with bonding support, for example, SuSE Linux Enterprise Server 9. SuSE SLES 9’s networking configuration system does support bonding, however, at this writing, the YaST system configuration front end does not provide any means to work with bonding devices. Sep 06, 2008 · Linux Networking HOWTO - Senthil Kumaran. v1.6 Sep 2008. Revision history list change only for major upates. Revision 1.6 is Wikification of How to. Revision v1.5 Aug 1999 ; List of Authors: Terry Dawson (main author) Alessandro Rubini. Joshua Drake (Poet) (Former Maintainer) Section 3: Brief howto using MULTIQ for multiqueue devices¶ The userspace command ‘tc,’ part of the iproute2 package, is used to configure qdiscs. To add the MULTIQ qdisc to your network device, assuming the device is called eth0, run the following command: Jan 23, 2018 · Use the following commands as per your Linux distribution to restart the networking service. You must run the command as root user either using sudo or su commands. The ifup command bring a network interface up. Linux Networking Paul Cobbaut Paul Cobbaut Publication date 2015-05-24 CEST Abstract This book is meant to be used in an instructor-led training. For self-study, the intent is to read this book next to a working Linux computer so you can immediately do every subject, practicing each command.